Universal Extra Long Wires 21 Circuit Wiring Harness Hotrod Kit Compatible with GM Chevy Universal Automotive Wiring
Price: $16.99 - $108.88
(as of Sep 24, 2024 06:12:50 UTC – Details)
Product Description
THE SQ-DUBNAG WIRING SYSTEM:
1X PRE-WIRED FUSE PANEL WITH 17 FUSES AND 1 BREAKER
2X SIGNAL FLASHERS AND 1 PRE-WIRED RELAY CONNECTOR WITH HORN RELAY
2X PRE-WIRED HEADLIGHT PLUGS; 1X PRE-WIRED LATE GM ALTERNATOR PLUG
2X PRE-WIRED GM COLUMN IGNITION SWITCH PLUGS
1X PRE-WIRED DIMMER SWITCH PLUG
2X GM TURN SIGNAL CONNECTORS FOR THE PRE-TERMINATED WIRES (3 7/8″ AND 4 1/4″)
1X FUSIBLE LINK (3″ BLACK WIRE WITH RING TERMINAL)
1X LARGE GROMMET
30X PLUS MISCELLANEOUS INSULATED TERMINALS AND SOME SMALL CABLE TIES
2X LOOSE WIRES (NUETRAL SAFETY SWITCH WIRE AND PANEL LIGHT WIRE)
STEP #1
READ THESE INSTRUCTIONS before starting this installation. These instructions were developed after installing this system in over a dozen different vehicles and should make this a quick and SQ-DUBNAG job.
STEP #1
To aid you we have used BOLD PRINT to note IMPORTANT items and provided general diagrams for FORD, GM and MOPAR. There is also a DO’S and DON’TS section that you may find useful. Please remember that these are GENERAL INSTRUCTIONS for your UNIQUE and SPECIFIC vehicle and you may need to MODIFY them for your application. Also whenever using AFTER-MARKET or SPECIALITY equipment, always use the diagrams PROVIDED WITH that equipment.
STEP #1
This WORKBOOK is designed for both our labeled and color-coded harnesses. Whenever a specific wire is referred to, it will be displayed with its LABEL then it’s COLOR. You are to use the destination that applies to the kit you purchased. If a diagram shows ONLY a color OR a label then that wire is NOT PROVIDED by this kit. An example of this would be GROUND WIRES which we DO NOT provide. We do recommend the use of black for ground wires on our color-coded harness and white on our labeled black harness to eliminate possible confusion.
STEP #1
Remember this is a WORKBOOK!!! So make use of the blank space we provide for your notes. Write things down so you won’t forget.
STEP #2
COMPLETE THE WORK SHEET at the back of this workbook. This should be done while looking at the vehicle, so that you can identify what accessories you will be using and what switches will be necessary. Here is where A LITTLE PLANNING WILL SAVE A LOT OF TIME.The WORK SHEET has been divided into the same 4 basic sections that make-up your harness. They are the FRONT SECTION, DASH SECTION, STEERING COLUMN SECTION and TAIL SECTION.For each section compare the list of wires to your application and note if it will be USED, MOVED or REMOVED. Before marking wires to be removed consider accessories you may want to add at a later time or those not provided for by this kit. The design of your vehicle may require some of the wires to be moved form one section to another. (An example of this would be, if the horn was mounted on the rear of the car, you would want to move the HORN = GREEN wire to the tail section.) When marking a wire to be moved DON’T FORGET to WRITE IT into the new section in the extra spaces provided. The extra spaces should also be used for any extra wires you may need to add, such as ground wires.
SQ-DUBNAG WIRING’S DO’S AND DON’TS
DON’T LET THE SIZE OF THE JOB SCARE YOU. WE MAKE THIS INSTALLATION AN E-Z JON.DON’T START THIS INSTALLATION UNTIL BEFORE DISCONNECTING BOTH BATTERY CABLES.DO INSTALL MAIN GROUND CABLES FORM THE ENGINE TO THE FRAME AND FROM THE ENGINE TO THE BODY. MAIN GROUND CABLES SHOULD BE THE SAME SIZE AS THE BATTERY CABLESDO REMEMBER TO GROUND ALL ACCESSORIES.DON’T FORGET. A GOOD GROUND IS A CLEAN NO RUST NO PAINT CONNECTION TO METAL.DO USE CABLE TIES TO HELP LOOM AND SORT THE HARNESS. DO ROUTE THE WRIED BEFORE INSTALLING TERMINALS OR MAKING CONNEXTIONS. DO ROUTE THE WRIED OVER SHARP EDGS OR NEXT TO THE EXHAUST COMPONENTS. DO ROUTE THE WRIED TOO NEAR MOVING PARTS LIKE FANS,BELTS,STEERING GEAR,HOOD LATCHES OR HINDGES.DO FASTEN THE HARNESS DOWN WITH CLAMPS AND TIES TO KEEP IT SECURE.DON’T STRETCH WIRES TO MAKE THEM REACH. ALWAYS LENGTHEN AS NECESSARY.DO USE GROMMETS WHEN PASSING WIRES THROUGH HOLES; DO USE THE LOOM PROVIDED IN THE ENGINE COMPARTMENT; DO USE INSULATED TERMINALS OR HEAT SHRINK OVER THE CONNECTIONS; DO ALWAYS USE THE CORECT SIZE TERMINAL FOR THE GAUGE OF WIRE.DON’T OVER CRIMP THE TERMINALS. DON’T FORGET IF YOU ARE USING AN AMP METER, YOU MUST FALLOW THE SPECIAL INSTRUCTIONS ON THE DASH DIAGRAM.DO USE THE DIAGRAMS PROVIDED WTIH AFTER-MARKET OR SPECIALTY ACCESSORIES.DON’T SKIP AROUND-STEAT A SECTION AND FINISH IT. DON’T FORGET TO DO THE WORK SHEET, IT WILL SAVE YOU A LOT OF TIME.DON’T FORGET THESE ARE ONLY GENERAL INSTRUCTIONS AND YOU MAY NEED TO MODIFT THEM FOR YOUR VEHICLE.DON’T DISCARD THESE INSTRUCTIONS WHEN YOU ARE FINISHED. THIS WORJBOOD AND YOUR NOTES WILL BE USEFUL LATER IF YOU ARE ADDING ON OR MAKING REPAIRS.
STEP #5
ROUTING AND ATTACHING THE WIRES. In this step you will be completing the job by terminating all those loose ends. As before this will be done section by section. We suggest you start with the TAIL SECTION and end with the DASH SECTION. Each section has its own set of instructions and we suggest you review the DO’S and DON’TS page and your WORK SHEET before starting each section. As you complete each section use cable ties to group the wires together and at points where wires branch off form the harness.The TAIL SECTION harness is designed to be routed to the back of the vehicle inside along the floor. The wires can be taped to the floor or run under the driver’s side door sills.They need to be routed where they WON’T BE WALKED ON and where the seats won’t interfere. At the rear of the vehicle you will attach the wires you your lights, gas tank sender, and fuel pump as indicated on the TAIL SECTION DIAGRAM. Please note also that the DOME LIGHT power wire is included in the TAIL SECTION.
IF YOU NEED INSTALLATION INSTRUCTIONS, WE WILL SEND YOU TO MEET YOUR NEEDS ! ! !
Add to Cart
Add to Cart
Add to Cart
Customer Reviews
4.2 out of 5 stars
445
4.3 out of 5 stars
195
3.9 out of 5 stars
222
Price
$108.88$108.88 $43.99$43.99 $38.99$38.99
Installation Instructions
✓
✓
✓
Fitment
Universal Universal Universal
Package Dimensions : 11.57 x 11.02 x 5.91 inches; 9.79 Pounds
Date First Available : March 7, 2020
Manufacturer : ay-autoparts
ASIN : B085MFS4PP
💫17 fuses and 21 circuits; GM column connectors are included
💫All wires are labeled every 5 inches so installation is easy
💫To make installation even easier, the wires are GM color coded
💫GM installations see photos above
💫Package includes wiper/radio acc, cruise/backup, heater/air, clock, dome, cig lighter, crtsy power, power door, power seat, fan power, coil, choke, instrument power, flasher, fuel pump power, brake, power window, headlight, radio battery, horn.
Customers say
Customers like the value for money of the cable assembly. However, some customers have reported that the wiring instructions are hard to read and the words on the wiring are not big enough. Opinions are mixed on the wire labeling, quality, and circuit functionality.
AI-generated from the text of customer reviews
